|
|
SCALEPRO SIMULATOR 4 Bright yellow case to increase visibility in the field. Crush-tested to 500#, dustproof, waterproof, and floats (with lid properly closed.) Calibrated range: 0-3 mv, 0.25 steps. Ten-turn potentiometer allows variable analog ranges of + 0.25 or + 0.50 mv/v around any step. Four modes: simulator, simulator with fixed +0.25 mv/v offset, variable simulator with steps of +0.25 or +0.50. Variable power supply loading: switch 1, 2, 3, 4 or 350 ohm cells. |
| Click Here For A Quote |
|
|
SIMULATOR 5 Light-weight, inexpensive, basic simulator. Excellent for bench work where multiple simulators are needed for testing indicators. Four brightly colored binder posts for easy connections- just push stripped wire throug hhole and turn top. Calibrated outputs- 0.0 to 3.00 mv/v in 12 steps. Size: 4-1/8"L x 2 13/16"W x 2 -1/16" H overall. Plastic case. Fits in shirt pocket, tool box, or glove compartment. Never be without one again! |
| Click Here For A Quote |
|
|
UJB-100T10 TEN CHANNEL J-BOX 10 CHANNEL UNIVERSAL JUNCTION BOX WITH TRANSIENT PROTECTION Signal or excitation trim, series-type transient protection; individual cell trim and section trim, (either can be disabled if not required). For load cells with impedances from 240 to 2000 ohms; can have 1 thru 10 channels. REPLACEMENT J-BOX FOR ALMOST ALL APPLICATIONS IN THE FIELD. Dip switches set up box to match your requirements. Standard enclosure is NEMA 4X fiberglass JIC 8" x 6" x 3-1/2" with nylon cord grips. Ground cord included. |
| Click Here For A Quote |
|
|
UJB-10LCT TEN CHANNEL J-BOX 10 CHANNEL SIGNAL TRIM JUNCTION BOX WITH TRANSIENT PROTECTION Signal trim, series-type transient protection; individual cell trim and section trim. For load cells with impedances from 240 to 2000 ohms. J-box can have 2, 4, 6, 8, or 10 channels. Standard enclosure is JIC 8" x 6" x 3-1/2" NEMA 4X fiberglass with nylon cord grips installed (F). Also available in stainless steel (SS) or as board only (BO). Ground cord included. |
| Click Here For A Quote |
|
|
SCALE-PRO® 1260 8 CHANNEL J-BOX WITH TRANSIENT PROTECTION, Signal Trim with section trim and individual trim for 8 load cells only. Large screws; one for each load cell and one for indicator. Two series isolation resistors limit zero interaction. Includes gas tubes to help stop "spikes".Available as board only or in NEMA 4X fiberglass enclosure with 9 nylon strain reliefs. Board size: 6-7/8" x 8-3/4". Fits standard JIC 8" x 10" enclosure. |
| Click Here For A Quote |
|
|
UJB-4 MID-SIZE J-BOX, EXCITATION TRIM, 2 TO 4 CELLS; 6 TO 8 PARALLEL Excitation trim with individual cell, for 2 to 4 single cells, 6 to 8 cells if connected in parallel with expansion port. Accepts #12 AWG, has 4 100k 25-turn cermet pots. Circuit board size: 8" x 4.5". Available as board only, in fiberglass, or explosion-proof enclosure. |
| Click Here For A Quote |
|
|
UJB-6 MID-SIZE J-BOX, SIGNAL TRIM, 6 TO 8 CELLS Designed for 4 single cells, 6 to 8 cells if connected in parallel. Connectors accept spade lugs, tinned leads or bare wires up to #12 AWG. Has 4, 100K, 25 -turn cermet pots, 35-50 ppm/C° typical. Circuit board size: 8" x 4.5". Available as board only, larger size NEMA 4X fiberglass enclosure with 5 nylon strain reliefs, or in explosion-proof. NOTE: Must be modified for use with less than four cells. |
| Click Here For A Quote |
|
|
TRIMASTER SCALE-PRO® TRIM-MASTER, MID-SIZE J-BOX SIGNAL TRIM, 4 CELLS Individual or section trim. Section trim can be disabled if desired. NOTE: This board may not be used with less than 4 load cells without modification. Fits a standard JIC 806 enclosure. May be attached to additional Trim-masters through the expansion connector. Available as board only, in fiberglass,or stainless steel enclosures. Board size; 6-3/4" x 4-7/8". |
| Click Here For A Quote |
|
|
SS406 SMALL J-BOX 4 CELL, SIGNAL TRIM Compact junction box with signal trim for 4 load cells. Use for 4 cell applications. Contains one multi-turn pot for each load cell. Available with lever-type connectors or screw terminals. Accepts wire sizes 14 to 26 AWG. Five nylon strain reliefs, gasketed lid, stainless enclosure with mounting ears. Size: 7-3/4" x 5- 1/4" x 1-5/8" overall. Board size:3-13/16" x 2-5/16". Also available with resistor networks for greater stability in platform scales. |
| Click Here For A Quote |
|
|
SS604 SMALL J-BOX, 4 CELL, EXCITATION TRIM Standard small, four load cell, excitation trim J-box with four screw-terminal connectors and individual trim. Circuit board is pre-mounted in a stainless steel enclosure with stainless screws. Enclosure has five 3/8" nylon strain reliefs (hubs) and one 1/2" hub, gasketed lid, four lid screws and washers, and instructions. Overall enclosure size: 7-3/4 x 5-1/4" x 1-5/8". Board size; 3.8" x 2.3". |
| Click Here For A Quote |
|
|
SS400W SMALL J-BOX, NO TRIM POTS For matched cells which need no trimming, the SS400W features premiumWago® connectors- no screws or soldering. Excitation trim. The SS400W has no trimming or isolation components which might alter the outputs from matched cells. If trim is required, separate turrets are provided for wire-wound trim resistors on top of the board. The stainless steel enclosure is rated NEMA 4X for areas where corrosion and water resistance are essential. Enclosure dimensions: 7-3/4" x 5-1/4" x 1-5/8". Also available as board only. Board dimensions: 3.8" x 2.3". |
| Click Here For A Quote |
|
|
|
LTP-1 AC STAINLESS TRANSIENT PROTECTOR Protects against spikes and short duration surges while providing superior EMI/RFI suppression. Contains series-type filters with bi-directional design. REQUIRES GROUNDED OUTLET FOR PROPER OPERATION. Operating voltage: 120 VAC,50/60 Hz nominal; maximum current: 10 Amps rms instantaneous, 7 Amps rms continuous. Available in stainless steel (standard) or fiberglass and can be desk or wall mounted. 220 VAC optional. Overall size: 6" x 8" x 2 -1/2" H.
|
| Click Here For A Quote |
|
|
LCP-1 Small DC Load cell transient protector , 4 channel Cost effective, self-contained, easy to install. Encapsulated circuitry eliminates fungus, PVC enclosure is inert to most chemicals. Ground cord included. Four channel, series-type protection with separate shield protection and ground. Maximum excitation voltage: 20 VDC or 20 VAC. Overall size: 6 -1/4" x 5 -7/16 " x 2 -1/2"H. PVC ENCLOSURE IS NOT INTENDED FOR WASHDOWN OR SUBMERSION. Requires optional sealing kit to meet NEMA 4X or NEMA 6 standard. Available with standard nylon hubs or Myers conduit fittings. |
| Click Here For A Quote |
|
|
LCP-2 SmallDC Load cell transient protector with remote sense, 6 channel Cost effective, self-contained, easy to install. Encapsulated circuitry eliminates fungus, PVC enclosure is inert to most chemicals. Ground cord included. Four or six channel, series-type protection with separate shield protection and ground. Maximum excitation voltage: 20 VDC or 20 VAC. Overall size: 6 -1/4" x 5 -7/16" x 2 -1/2"H. PVC ENCLOSURE IS NOT INTENDED FOR WASHDOWN OR SUBMERSION. Requires optional sealing kit to meet NEMA 4X or NEMA 6 standard. Available with standard nylon hubs or Myers conduit fittings. |
| Click Here For A Quote |
|
|
UJB-3T6 Mid-size DC Load cell transient protector with remote sense Protects up to 6 serial communications lines and up to 8 parallel or summed load cells from voltage transients. Six channel with shield protection and large terminal strips with #6 SEMS screws for wires up to #12 AWG. 50K baud max transmission rate. Compatible with signal down to 1µV grad. Clamping time: 75 VDC stages <100 nanoseconds typical. Clamping voltage: 75 VDC or 75 VAC. Peak surge currents: 75 VDC stage-5000 amps. Series resistance: 0.219 typical. Series inductance: 110µh typical. Max excitation voltage: 20 VDC or 20 VAC. NEMA 4X FRP enclosure. Mounting screws and #10 AWG ground wire included. Two nylon strain reliefs for 0.079"- 0.236" diameter cable. Circuit board: 6.75" x 4.75". Enclosure size: 7.63"W x 6.63"H x 3.25"D. |
| Click Here For A Quote |
 |
 |
